Table of contents:

Remove carpeting: the best tips
Remove carpeting: the best tips
Video: Remove carpeting: the best tips
Video: How to remove carpet cleanly - DIY 2023, February
Anonim

Carpeting was the trend of the 1970s and no household could be imagined without it. But what if the old carpet is getting old? Stains, age-related traces or the desire for something new: there are many reasons for a new floor covering. With this step-by-step guide, you can easily remove your old carpet.

Table of contents Table of contents Remove old carpeting: With these tips you can do it

  • Step 1: Remove the carpet strips
  • Step 2: Check the carpet bonding
  • Step 3: Remove any adhesive residue
  • Removing carpets: the most important things in brief:

Table of contents Table of contents Remove old carpeting: With these tips you can do it

  • Step 1: Remove the carpet strips
  • Step 2: Check the carpet bonding
  • Step 3: Remove any adhesive residue
  • Removing carpets: the most important things in brief:

Step 1: Remove the carpet strips

Before you can remove the carpet, you must first remove the existing baseboards, which are used to cover the gap between the carpet and the wall. To do this, slide a spatula behind the bar and carefully pry it off the wall - baseboards fixed with steel nails can usually be easily removed. If the strips are screwed together, you must first remove the screws to avoid damaging the wallpaper and wall. Plastic baseboards are often covered with carpeting strips on the front - these should be disposed of and replaced with new ones, because removing the old carpet remnants is often very difficult due to the strong bonding with double-sided adhesive tape.

Image
Image

Step 2: Check the carpet bonding

To determine how best to remove the carpet, you need to check the gluing of your flooring. If you first loosen the carpet at one corner, you can find out whether it has been glued to the surface or is only attached with adhesive tape.

The following measures are necessary depending on the type of gluing:

If only the edges of the floor covering are glued with double-sided adhesive tape, it can be removed relatively easily. First tear off the rubberized back of the carpet from the adhesive strip. Then cut the carpet into strips and roll them up one after the other. So you can easily dispose of them in a garbage bag. Only then remove the old tape from the floor with a sharp spatula. Tip: If it sticks strongly, you should heat it up with a hot air dryer - this will make it easier to remove it from the screed.

Image
Image

Is the carpet firmly glued?

The best trick to test which glue was used to fix the carpet: dampen a corner with boiling water and let it soak into the carpet. After waiting two hours, start carefully lifting the carpet at this corner.

If you can easily remove the carpet, the adhesive is water-soluble glue. Good news, because with the help of hot water and a little patience, removing the old carpet is no problem. With a metal watering can you can easily moisten the entire surface. After a contact time of about two hours, the carpet, best cut into strips, can be easily removed.

If the carpet cannot be removed or is difficult to remove after moistening, it is synthetic resin or another water-insoluble adhesive. In this case, removing the old carpet is much more difficult and requires patience as well as strength.

Use a carpet knife or cutter to cut your carpet into strips about 30 to 50 centimeters wide - but be careful not to damage the floor underneath. For such cases, there are so-called hook blades for carpet knives that are blunt on the underside.

Image
Image

After cutting the carpet, start in a corner and then pull the strips off with a jerk. This way you can loosen the entire carpet step by step, whereby the rubberized back often sticks to the screed over a large area. In this case there is technical support: the so-called stripper is a mechanical device that you can borrow in any hardware store for a fee of around 35 euros per day. Depending on the performance of the device, the rental costs may also be higher. Check which model is sufficient for your needs. The stripper pushes a blade under the carpet and removes this step by step. Alternatively, you can also work with a multi-function tool.

Anyone who prepares will be rewarded: First cut the carpet into strips even when using a stripper, paying attention to the width of the stripper. If the stripes are a bit narrower than the blade, working with the stripper works best. Always start at a seam or edge when loosening the carpet with a stripper.

When the carpets are removed mechanically, the development of dust is even stronger than with the manual method. Therefore, you should keep the doors closed, open all windows and wear a dust mask. The most effective way to remove dust is with an industrial vacuum cleaner from the hardware store.

Incidentally, the particularly stubborn carpet adhesives, which are difficult to remove, are often two-component adhesives. These adhesives were used frequently in the 1970s and can be recognized by the yellow adhesive residue. With these carpet adhesives, experienced craftsmen even advise to sand the screed.

Image
Image

Step 3: Remove any adhesive residue

After removing the carpet, you must completely remove the remaining adhesive residue. Because even well-bonded old adhesive can cause nasty surprises when laying the new flooring when it comes into contact with the new adhesive - from chemical reactions to the formation of bubbles.

It takes some strength and time to clean the screed if you scrape off the remains with a spatula. When removing the adhesive or foam residues, it is better not to use nitro-containing solvents - even in low doses, they are hazardous to health and are not suitable for removing carpeting. Alternatively, there are special solvents for removing carpet glue. It is imperative that you follow the instructions for use regarding the amount and the exposure time. With the help of these products, most adhesives can be removed relatively easily.

Once the old carpet has been completely removed, you should prepare the floor for the new covering. With a leveling compound from the hardware store, you can remove cracks and unevenness in the screed and create a good basis for the new flooring. Our tip: For large areas or severe damage, you can also use a floor grinder. Finally, prepare the floor with a primer for the new flooring.

When removing carpets, always remember that, especially in older houses, high-quality parquet floors or beautiful wooden floorboards can be hidden under the old carpeting. Help these "mineral resources" to a new shine: Simply remove the scratches created when removing the old carpet by sanding and then seal the wood with wax or oil.

Removing carpets: the most important things in brief:

  • Remove the baseboards and cut the carpet into strips before removing.
  • Check the bond and use a stripper for stubborn adhesives.
  • Remove adhesive residue with a spatula and suitable solvents. In case of doubt, a grinding machine helps.

After the old carpet is removed, it is time for a new floor covering. You can get offers near you here:

Carolin Haist

Popular by topic